Skip to main content

2023 WOR: Point Fire (Idaho) – July 28, 1995

 Day 1  |  Day 2  |  Day 3  |  Day 4  |  Day 5  |  Day 6  |  Day 7

 

Point Fire (Idaho) – July 28, 1995

Today’s topic is dedicated to all fallen firefighters.
May we never stop learning.

 

On July 28, 1995, at 6:29 p.m., a fire was reported approximately 16 miles southwest of Boise. Bureau of Land Management (BLM) and Kuna Rural Fire District (RFD) resources were dispatched to the fire. As they arrived on scene, the fire was 60 to 65 acres, actively burning in brush and grass with moderate rates of spread. The BLM Incident Commander (IC) instructed the BLM engines to split up and directly attack the flanks with Kuna RFD engines 620 and 622 behind them. The fire spread had been stopped at 120 acres.

 

At 8:22 p.m., the National Weather Service issued a Red Flag warning predicting gusts of up to 50 mph from a thunderstorm.

Kuna 620 and 622 mopped up along the north flank until 622 ran out of water. While Kuna 622 was en route to refill, Kuna 620 contacted them with a report that their vehicle was overheating. Kuna 620 turned north on a two-track road, driving cross-country through unburned heavy sagebrush. At this point, Kuna 620 became disabled.

At about 8:46 p.m., the fire escaped the northern flank due to strong southerly outflow winds. Several fire personnel immediately drove north to assess fire behavior. They see a stationary engine in the path of the oncoming flame front. They did not know whether the engine was occupied.

Never Forgotten

  • Bill Buttram (31)
  • Josh Oliver (18)

At, 8:49 p.m., Kuna 620 contacted the Kuna Commander on a local non-federal frequency and reported, “We are on the north line. We have fire coming hard, and this thing has died.” The Kuna 620 engine crew made another radio transmission one minute later, “The truck’s been overtaken by fire!” That was their last transmission. It took four minutes from the point of escape for the fire to overrun the disabled engine.

How do we as a fire community remember and honor those that were lost.
Understanding how federal, state, and local resources come together on a single piece of ground to accomplish a common goal will continue to make the response to wildfire, prescribed fire, and all-hazard incidents better.

How do you maintain, improve, or promote relations on your unit?
The focus on our quality of engines and support vehicles throughout the fire service is constantly improving. The improvements made in standardizing the Preventative Maintenance checks and creating a culture of reporting equipment issues nationally have helped tremendously.

What are ways you ensure your equipment is in serviceable condition?
In the Swiss Cheese model, the holes in the slices represent weaknesses in individual parts of the system and are continually varying in size and position across the slices. The system produces failures when a hole in each slice momentarily aligns, so that a hazard passes through holes in all the slices, leading to a failure. In the case of the Point Fire there wasn’t a singular event that led to this tragedy. Recognition of all the different variables is key in learning.

Resources:

Last Modified / Reviewed:

Have an idea or feedback?

Share it with the NWCG 6MFS Subcommittee.


Follow NWCG on Twitter and Facebook

NWCG Latest Announcements

NWCG Equipment Technology Committee Releases Safety Warning: 24-001 Stihl Chainsaw Toolless Fuel Cap Spill Prevention

Date: November 14, 2024
Contact: Equipment Technology Committee

The Equipment Technology Committee (ETC) has released Safety Warning: 24-001 Stihl Chainsaw Toolless Fuel Cap Spill Prevention. Misaligned toolless fuel caps on Stihl chainsaws have led to recurring fuel spillage, fuel ignition, and burn injuries during wildland fire management operations.

This Safety Warning is intended to highlight the details and recommended procedures for the installation of a Stihl chainsaw toolless fuel cap, as well as how to identify and correct a misaligned, damaged, or broken fuel cap to help prevent fuel spillage.

References:

NWCG Safety Warning: 24-001 Stihl Chainsaw Toolless Fuel Cap Spill Prevention

Advertencia de equipos 24-001: Prevención de derrames de la tapa de combustible sin herramientas de la motosierra Stihl

NWCG Alerts

The Incident Position Standards and Next Generation Position Task Book are now available for Equipment Time Recorder (EQTR)

Date: November 13, 2024
Contact: Incident Business Committee

NWCG is excited to announce that the NWCG Incident Position Standards for Equipment Time Recorder, PMS 350-51 and NWCG Position Task Book for Equipment Time Recorder (EQTR), PMS 311-51 are now available.

The Performance Support Package, which for EQTR, includes the Incident Position Standards and Next Generation Position Task Book were developed through the Incident Performance and Training Modernization (IPTM) effort. The Performance Support Package will support trainees, those qualified in the position, and evaluators.

References:

NWCG Equipment Time Recorder Position Page

NWCG Incident Position Standards for Equipment Time Recorder, PMS 350-51

NWCG Position Task Book for Equipment Time Recorder (EQTR), PMS 311-51

The Incident Position Standards and Next Generation Position Task Book are now available for Personnel Time Recorder (PTRC)

Date: November 13, 2024
Contact: Incident Business Committee

NWCG is excited to announce that the NWCG Incident Position Standards for Personnel Time Recorder, PMS 350-53 and NWCG Position Task Book for Personnel Time Recorder (PTRC), PMS 311-53 are now available.

The Performance Support Package, which for PTRC, includes the Incident Position Standards and Next Generation Position Task Book were developed through the Incident Performance and Training Modernization (IPTM) effort. The Performance Support Package will support trainees, those qualified in the position, and evaluators.

References:

NWCG Personnel Time Recorder Position Page

NWCG Incident Position Standards for Personnel Time Recorder, PMS 350-53

NWCG Position Task Book for Personnel Time Recorder (PTRC), PMS 311-53

NWCG Risk Management Committee Releases Safety Bulletin: 24-001 Use of Respirators on Wildland Fires

Date: November 7, 2024
Contact: Risk Management Committee

The Risk Management Committee (RMC) has released Safety Bulletin: 24-001 Use of Respirators on Wildland Fires. As wildland fire respirators are available through several established vendors, wildland fire personnel need to understand regulations and limitations of respirator use in the workplace.

Safety Bulletin 24-001 outlines the following topics regarding respirator use for wildland fires:

  • Requirements for Respirator Use
  • Voluntary Respirator Use
  • Current Respirator Options
  • Unknown Risks of Respirator Use

This bulletin also provides mitigation recommendations to help reduce smoke exposure for wildland firefighting efforts.

References:

NWCG Safety Bulletin: 24-001 Use of Respirators on Wildland Fires

NWCG Smoke Management Guide for Prescribed Fire, PMS 420-3

VIDEO: Protecting Wildfire Personnel from Smoke - How Incident Management Teams Address Smokes Risks

VIDEO: Smoke, Knowing the Risks