Skip to main content

PMS 448

PMS 448

Introduction

COVID-19 Refurb Guidelines

References

All Categories

Aviation

Camp

Clothing

Cordura

Fuel Handling

Kits

Medical

Miscellaneous

PPE

Small Engine Equipment

Tools

Water Handling

Deleted Items

Valve – Wye, Gated, Brass, 3/4” NH-F X 3/4” NF-M X 3/4” NH-M

NFES #
000904
Category
Water Handling
Updated
Storage and Shelf Life Checks
None

Initial Inspection/Disposal Criteria

  1. Inspect for the following:
    1. Handles-bent, broken, missing, too tight, too loose, expansion pins coming out or missing, handles correct (left and right) and positioned properly.
    2. Male flange-flange missing, lock-ring and set-screws functional, damaged threads, smooth flat surface on flange, burrs on threads, or loose male flange.
    3. Female coupling-Coupling spins freely, gasket present and in good condition, free of cracks, damage, or burrs on threads.
    4. Casting (body)-Fire damage—look for further damage, O-rings in good condition, corrosion, cracks, and burrs.
    5. Plastic sphere-Inspect sphere while turning handle; if pitted or rough, replace.
  2. Return to stock if item is clean, passes inspection, and is in unused condition.
  3. Refurbish if deficiencies are discovered during the inspection process and item requires cleaning.
  4. Dispose of item if damages are not repairable or item has sustained damage caused by fire.

Refurbishing Procedures

A. Cleaning

  1. Clean in a mild detergent with brush and scouring pad or use parts washer or high-pressure wash to remove foreign matter such as mud, dirt, or grease. Rinse thoroughly.
  2. Do not soak for extended periods of time as detergent will corrode the metal.
  3. Stand upright with barrels in open position to drain water and dry.
  4. Lubricate with appropriate type of lubricant.

B. Repair

  1. Replace missing or damaged O-rings and gaskets.
  2. Replace broken, missing handles.
  3. Repair or replace male flange if damaged is discovered on face or threads.
  4. Replace female coupling or bearings if not spinning freely.

C. Testing for Performance

  1. Install valve on test pump.
  2. Turn on water to pump and open valve to expel air then close valve.
  3. Turn on pump
  4. NFES #000259 and NFES #000231 test at 300 PSI for 3 minutes.
  5. NFES #000904 test at 100 PSI for 3 minutes.
  6. Inspect for leaks around the gasket, at the handles, and around flanges while on test pump.
  7. If valve leaks, repair as necessary, or dispose of through local procedures.
  8. Retest after repairs are made.

D. Repackaging

  1. Ensure item is completely dry prior to packaging.
  2. Packaging: 
    • Use NFES #008064 carton (10” x 8” x 6”) for a standard pack of 50 EA.

 

Reference

Water Handling Equipment Guide, PMS 447-1 

 

Share on Social Media

Print PDF

NWCG Latest Announcements

NEW! M-280, Resource Advisor, Fireline (Instructor-Led) Course Available Now

Date: January 29, 2026
Questions? 
Please contact: Resource Advisor Subcommittee

NWCG is pleased to announce the new M-280, Resource Advisor, Fireline (Instructor-Led) course is now available. This training supports individuals working towards Resource Advisor, Fireline (REAF) incident qualifications.

M-280, Resource Advisor, Fireline (Instructor-Led) training prepares students to serve as a Resource Advisor, Fireline (REAF) as defined in NWCG Incident Position Standards for Resource Advisor, Fireline, PMS 350-112. This course presents scenarios that reflect the diverse challenges a REAF may encounter during an incident. Through these scenarios, participants gain hands-on experience and an understanding of REAF responsibilities in a controlled learning environment.

References:

Resource Advisor, Fireline Position Page

NWCG Position Standards for Resource Advisor, Fireline, PMS 350-112

M-280, Resource Advisor, Fireline (Instructor-Led)

Wildland Fire Learning Portal

2026 Updates to the NWCG Standards for Wildland Fire Position Qualifications, PMS 310-1

Date: January 23, 2026
Questions? 
Please contact: Incident and Position Standards Committee

The Incident and Position Standards Committee has updated the NWCG Standards for Wildland Fire Position Qualifications, PMS 310-1.

These updates address changes to incident position names and requirements for qualification, training, and experience. Updates related to the implementation of Complex Incident Management (CIM) and Incident Performance Training Modernization (IPTM) are also included.

The NWCG Wildland Fire Position Qualification Flowchart, PMS 308 has also been updated to reflect the recent changes.

References:

NWCG Standards for Wildland Fire Position Qualifications, PMS 310-1

NWCG Wildland Fire Position Qualification Flowchart, PMS 308

IPSC Memo 26-01: January 2026 Updates to the NWCG Standards for Wildland Fire Positions Qualifications, PMS 310-1

Incident Business Committee Memo 26-01: Updated Emergency Equipment Shift Ticket, OF 297

Date: January 22, 2026
Questions? 
Please contact: Incident Business Committee

The Incident Business Committee (IBC) has released Memorandum 26-01: OF 297 and 2026 Fire Use. This memo informs the wildland fire community that the updated Emergency Equipment Shift Ticket, OF 297 is available for download and can be ordered through the Great Basin Cache.

Beginning January 15, 2026 the previous version of the OF 297 form has been discontinued.

For further details, please contact your IBC representative.

References:

Incident Business Committee Memorandum 26-01

Great Basin Cache

NEW! S-390, Introduction to Wildland Fire Behavior Calculations (Blended) Available Now

Date: December 22, 2025
Questions about RT-130? 
Please contact: Fire Behavior Subcommittee

NWCG is excited to announce that the new S-390, Introduction to Wildland Fire Behavior Calculations (Blended) training is now available on the Wildland Fire Learning Portal.

This third course in the series combines online and instructor-led training components aimed at individuals who are involved in planning, managing, and executing wildland fire and prescribed burn operations; who require a thorough understanding of fire behavior calculations to enhance effectiveness and safety. This includes students who require the knowledge and skill necessary to perform the duties of a Type 3 Incident Commander (ICT3), Division/Group Supervisor (DIVS), or Prescribed Fire Burn Boss Type 2 (RXB2).

Students are required to be qualified as any Single Resource Boss position and complete the prerequisite S-290, Intermediate Wildland Fire behavior (Blended) course, before enrolling in S-390.

References:

S-390, Introduction to Wildland Fire Behavior Calculations (Blended)

Wildland Fire Learning Portal