Skip to main content

PMS 448

Axe – 3-5lb., 26" Straight Handle w/Sheath

NFES #
000383
Category
Tools
Updated
Storage and Shelf Life Checks
None

Initial Inspection/Disposal Criteria

  1. Inspect for obvious damage to head, cutting edges.
  2. Inspect for large chips in blade or cracked head eye.
  3. Inspect for any modifications to head, such as rivets through side of head to hold handle.
  4. Inspect handle for twisted, bent or open grain, if handle has been shortened or is non-standard.
  5. Return to stock if item shows no signs of use and passes visual inspection.
  6.  Refurbish if damage detected in the inspection process is repairable or handle is replaceable.
  7. Dispose of item if unable to repair.

Refurbishing Procedure

A. Cleaning

  1. Wash head and handle.
  2. Wipe dry.

B. Repair

  1. Head
    •  Sharpen tool to specifications according to tool sharpening gauge NFES# 000510.
    • Tools should never be ground to the degree that the metal temperature raises high enough to remove temper, i.e. blue or burned edges.
    • Ensure that blade corners are square.
    • Paint tool head with rust inhibitor (cache option.)
  2. Handle
    • Sand handle if it is rough, chipped, dinged, or has any type of residue that did not come off during sanding.
    • When replacing handle, shape eye for a snug fit. Use high impact plastic or wood-type wedges with appropriate type of epoxy. Metal wedges can be added only in the field as an emergency measure and should not be used during refurbishment.
    • The bottom of the tool head should be within ⅜”--⅝” of the shoulder of the handle.
    • Cut excess off handle make flush with tool head after inserting wedge into handle.
    • Wipe handle with rag and linseed oil.

C. Tests for Performance

  1. On the head check that blades have not been tapered or rounded to the point that tools cannot be sharpened.
  2. On the handle check that it is not twisted, bent or is open-grain.
  3. Grasp the handle of the tool 2- 4” from the end with the head hanging down, but not touching the ground. Using a ball peen or similar hammer give the end of the handle a firm smack. Listen to the sound it makes. If the head is tight and the handle is free of defects, it will make a clear ringing sound. If it is loose or defective you will hear a dull thud, like hitting the end of a 2 x 4.

D. Repackaging

  1. For NFES #000707 install sheath (no NFES).
    • Package 12 each in NFES #000338 carton (37” x 18” x 7”).
  2. For NFES #000352 install leather sheath NFES #000359, package per local cache requirements.
  3. For NFES #000383 install sheath NFES #000815.
    • Suggested packaging is 6 each in NFES #000385 carton (7.25” x 9.25” x 26”).

NWCG Latest Announcements

ETC/RMC Safety Bulletin: 25-001 New Guidance on Laundering Wildland Fire Clothing to Reduce Contamination

Date: Aug 8, 2025
Questions? Please contact:
Equipment Technology Committee
 Risk Management Committee

The Equipment Technology Committee (ETC) and the Risk Management Committee (RMC) have issued Safety Bulletin 25-001: Laundering to Decontaminate Wildland Fire Clothing. Recent research revealed that wildland fire flame-resistant pants and shirts can be contaminated with chemicals from combustion byproducts, including carcinogens, and that common laundering practices can effectively remove these harmful contaminants from wildland firefighter clothing more effectively than previously understood. It is recommended to decontaminate wildland fire clothing as frequently as possible. 

Frequently Asked Questions about this new information and how to implement recommendations can be found on the NWCG Alerts page. Read the complete ETC/RMC Safety Bulletin: 25-001 to learn more. 

References:

NWCG Alerts

ETC Safety Bulletin: 25-001

Frequently Asked Questions (FAQ) on Laundering to Decontaminate Wildland Fire Clothing

Equipment Technology Committee

Risk Management Committee

FAQ Now Available for Archiving Type 1 and Type 2 Incident Positions

Date: Aug 6, 2025
Questions? Please contact:
Incident and Position Standards Committee

To support the transition to Complex Incident Management (CIM), NWCG will archive all Type 1 and Type 2 Command and General Staff (C&G) position qualifications in January 2026, as outlined in NWCG Executive Board Memo 25-002. To assist with this transition, a new Frequently Asked Questions (FAQ) document is now available.

This resource answers common questions about the status of Type 1 and Type 2 qualifications, impacts to incident qualification management, training requirements, and resource ordering considerations. Review the full FAQ to learn more.

For additional information on CIM and the transition of C&G positions, see NWCG Executive Board Memos 23-005, 24-005, and 25-002, as well as the Incident Workforce and Development Group webpage.

References:

NWCG Type 1 & Type 2 Position Archiving FAQ

NWCG Executive Board Correspondence

Incident Workforce Development Group

Incident and Position Standards Committee

Incident Position Standards and the Next Generation Position Task Books Now Available for UASD, UASM, UASL and UASP

Date: July 31, 2025
Questions?  Please contact:
Interagency Fire Unmanned Aircraft Systems Subcommittee
 

NWCG is excited to announce that Incident Position Standards and the Next Generation Position Task Books are now available for all four Unmanned Aircraft Systems positions:

  • Unmanned Aircraft Systems, Data Specialist (UASD)
  • Unmanned Aircraft Systems, Manager (UASM)
  • Unmanned Aircraft Systems, Module Leader (UASL)
  • Unmanned Aircraft Systems Pilot (UASP)

The Performance Support Packages for these positions were developed as part of the Incident Performance and Training Modernization effort. These resources support trainees, qualified personnel, and evaluators in their respective roles.

Any changes to qualification pathways will take effect with the next update of the NWCG Standards for Wildland Fire Position Qualifications, PMS 310-1, scheduled for January 2026.

References:

NWCG Unmanned Aircraft Systems, Data Specialist Position Page

NWCG Unmanned Aircraft Systems, Manager Position Page

NWCG Unmanned Aircraft Systems, Module Leader Position Page

NWCG Unmanned Aircraft Systems Pilot Position Page

Incident Position Standards and the Next Generation Position Task Books Now Available for RADO and INCM

Date: July 30, 2025
Questions?  Please contact:
Incident Logistics Subcommittee
 

NWCG is excited to announce that Incident Position Standards and the Next Generation Position Task Books are now available for Radio Operator (RADO) and Incident Communications Center Manager (INCM).

The Performance Support Packages for these positions were developed as part of the Incident Performance and Training Modernization effort. These resources support trainees, qualified personnel, and evaluators in their respective roles.

Any changes to qualification pathways will take effect with the next update of the NWCG Standards for Wildland Fire Position Qualifications, PMS 310-1, scheduled for January 2026.

References:

NWCG Radio Operator Position Page

NWCG Incident Communications Center Manager Position Page